2 - 1.5" self tapping screws 2 - 10-32 x 3/4" socket head screws 1 - advance kit 1 - gasket/o-ring seal 1 - tube of gear lubricant 2 - o-rings (chevy only) 1 - gray tach jumper warning: before installing the msd distributor, disconnect the battery cables. when disconnecting the battery cables, always remove the negative (-) cable frst and install it last. msd ready-to-run marine v8 distributor chevrolet, pn 83606, ford 351c-460, pn 83506 parts included: 1 - pro-billet distributor 1 - rotor, pn 8467 1 - distributor cap chevy, olds, pn 8565 ford, pn 8431 1 - wire retainer note: the terminals of this distributor require spark plug style terminals. you may need to change the terminals and boots of your wires. msd offers two kits, pn 8849 or pn 8848 that are supplied with nine boots and terminals. note: if the chevy gear is ever replaced, msd gear, pn 8561, is required for replacement due to the .500" diameter shaft. timing functions before continuing with the installation, here are a few defnitions you should be aware of: initial timing: this is the base timing (also referred to as idle timing) of the engine before the centrifugal advance begins. centrifugal advance: the centrifugal (or mechanical) advance mechanism is made up of weights, springs, advance cams, and an advance stop bushing. the amount and rate of advance that your distributor is capable of is determined by the centrifugal timing. if you ever wish to lock out the centrifugal advance, refer to the centrifugal advance section. total timing: this is the total of the initial timing plus the centrifugal advance added together. example: 10 initial + 25 centrifugal = 35 total timing. note: msd distributors are supplied with the heavy (slow) advance springs and the 21 stop bushing installed. this is to prevent detonation in certain applications. review the information on pages 2-4 to determine the best advance curve for your application. rpm limit and tachometer information tach signal: the ready-to-run distributor features a gray tach output wire which provides a clean signal for most tachometers and even some aftermarket fuel injection systems. the signal output is a 12 volt square wave, 20 duty cycle. this wire is also responsible for programming the built-in rev limiter. rev limiter: the ready-to-run distributor has a built-in rev limit that can easily be adjusted from 2,000 rpm to over 10,000 rpm. the default is 10,000 rpm. to set the rev limiter, run the engine to half the desired rpm then ground the gray tach wire (a jumper is supplied) for approximately one second. every time the key is turned to the on position, the tach will display the programmed rpm limit. see page 8 for the programming procedure. msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344 online product registration: register your msd product online. registering your product will help if there is ever a warranty issue with your product and helps the msd r&d team create new products that you ask for! go to www.msdperformance.com/registration.
2 installation instructions choosing an advance curve the function of the advance curve is to match the ignition timing to the burning rate of the fuel and speed (rpm) of the engine. any factor that changes the burning rate of the fuel or the engine speed can cause a need for an ignition timing change. figure 1 shows some of the factors that will affect engine timing. factor advance timing retard timing for for cylinder pressure low high vacuum high low energy of ignition low high fuel octane high low mixture (air/fuel) rich lean temperature cool hot combustion chamber shape open compact spark plug location offset center combustion turbulence low high load light heavy figure 1 ignition timing factors. as you can see from the chart, most factors will change throughout the range of the engine operation. the timing mechanism of the distributor must make timing changes based on these factors. example: an engine has 11:1 compression with a high energy ignition. with the specifcations given, you will have to retard the timing for the high compression and high energy ignition. by comparing the engines specifcations against the chart, a usable timing guideline can be found. engines with a combination of items from both columns will require a timing that is set in the mid range. obviously a full technical explanation of correct ignition timing would be very complicated. the best way to arrive at a suitable ignition curve for your engine is to use the ignition timing factors chart as a guide and compare it to the advance graphs in figure 4 until a suitable curve is found. when selecting your advance curve, use detonation (engine ping) as an indicator of too much advance, and a decrease in power as an indicator of too little advance. tips on selecting an advance curve ? use as much initial advance as possible without encountering excessive starter load. ? start the centrifugal advance just above the idle rpm. ? the starting point of the centrifugal advance curve is controlled by the installed length and tension of the spring. ? how quickly the centrifugal advance (slope) comes in is controlled by the spring stiffness. the stiffer the spring, the slower the advance curve. ? the amount of advance is controlled by the advance bushing. the bigger the bushing, the smaller the amount of advance. centrifugal advance curve selecting the advance springs the rate, or how quick the advance comes in is determined by the type of springs which are installed on the distributor. the msd distributors are equipped with two heavy silver springs installed. these will give you the slowest advance curve possible (figure 2). the parts kit contains two additional sets of springs which can be used to match the advance curve to your particular application. refer to the spring combination chart (figure 3) for combinations that can be achieved. msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
installation instructions 3 to change the springs, remove the cap and rotor and use needlenose pliers to remove the springs. be sure the new springs seat in the groove on the pin. red red red sil ver green blue purpl e bla ck sil ver green blue purpl e bla ck sil ver green blue purpl e bla ck sil ver green blue purpl e bla ck sil ver green blue purpl e bla ck sil ver green blue purpl e bla ck red red red advanced stop bushing advanced stop bushing advanced stop bushing advanced stop bushing advanced stop bushing advanced stop bushing figure 2 the factory equipped curve. timing curve from factory figure 3 spring combination chart. spring combination rate of advance figure 4 2- heavy silver slowest a 1- heavy silver b 1- light blue 1-heavy silver c 1-light silver 2- light blue d 1- light silver e 1- light blue 2- light silver fastest f figure 4 advance curves. msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
4 installation instructions figure 6 changing the advance stop bushing. selecting the advance stop bushing five different advance stop bushings are supplied in the distributor kit. the distributor comes with a blue (21) bushing already installed. if a different amount of centrifugal advance is desired, follow the next procedure to change the bushings. the chart in figure 5 gives the size and approximate degrees for the corresponding bushings. changing the advance stop bushings 1. remove the distributor cap and rotor. 2. remove the locknut and washer on the bottom of the advance assembly (figure 6). 3. remove the bushing and install the new one. install the washer and locknut. use care not to over-tighten. locking out the centrifugal advance 1. remove the advance components including the springs, weights and the advance stop bushing from the advance assembly. 2. for chevy models, remove the roll-pin from the drive gear and remove the gear from the shaft. for ford models, remove the roll pin from the shaft retaining sleeve and slide the sleeve down. 3. slide the shaft two inches out of the housing. 4. rotate the shaft 180 and insert the advance stop bushing pin into the small hole on the advance plate (figure 7). 5. install the locknut and washer to the advance stop bushing pin. this locks the advance in place. do not over-tighten the locknut. 6. install the drive gear or retaining sleeve and roll-pin. figure 6 locking out the centrifugal advance. figure 7 locking out the advance. figure 5 advance stop bushing chart. bushing size approximate crankshaft degrees red-smallest 28 silver 25 green 23 blue 21 purple 19 black-largest 18 msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
installation instructions 5 1. remove the existing distributor cap without disconnecting any of the spark plug wires. 2. with the cap off, crank the engine until the rotor is aimed at a fxed point on the engine or frewall. note this position by making a mark (figure 8). 3. place the distributor cap back on and note which plug wire the rotor is pointing to. mark the spark plug wires and remove the distributor cap. 4. disconnect the wiring from the distributor. 5. loosen the distributor hold down clamp and slide the clamp out of the way. 6. lift the distributor out of the engine. note that the rotor rotates as you lift the distributor out. this is due to the helical cut gear and should be taken into consideration when installing the new distributor. 7. install the gasket and apply a liberal amount of the supplied lubricant to the distributor gear. (the supplied o-rings can only be used if the chevrolet block has been modifed as shown in figure 9.) 8. install the distributor making sure that the rotor comes to rest pointing at the fxed mark. if the distributor will not fully seat with the rotor pointing to the marked position, you may need to rotate the oil pump shaft until the rotor lines up and the distributor fully seats. 9. position and tighten the hold down clamp onto the distributor. 10. install the distributor cap and spark plug wires one at a time to ensure correct location. a wire retainer is supplied to secure the wires in place. align the mounting bosses and use the supplied 1.5" self-tapping phillips screws to hold the retainer in place (figure 10). 11. page 7 shows how to set the rev limiter and connect the tachometer. figure 8 marking the rotor location. installing the distributor figure 9 modifed chevy block for use with o-rings. figure 10 installing the wire retainer. chamfer edges chamfer edges distributor housing o-rings rotor mark va lv e cover carb. msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
6 installation instructions warning: high voltage is present on the coil terminals. do not touch the terminals or coil tower when the engine is cranking or running. figure 12 connecting the marine ready-to-run distributor to a 6m-2 ignition control. figure 11 wiring the marine ready-to-run distributor. orange red black orange red black to ground to 12v ignition key + gray to tach input red orange black to coil positive + 12 volts to coil negative - to engine ground ig n itio n multiple spark discha rg e p art no . au to tr onic cont ro ls corpora tion serial no .. to t ach gra y msd 6m-2 marine ignition pn 6460 hea vy black hea vy red red to key ignition orange black coil to ba ttery + to ground to pn 8768 rev control + violet black to ground green + to 12 vol ts not used red orange black red orange white gray to tach input msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
installation instructions 7 tachometer information the msd ready-to-run has a gray wire that provides a 12 volt square wave, 20 duty cycle tachometer signal that will trigger most tachometers. it is recommended to connect this lead to your tachs trigger input wire and check its operation. note that the rpm limiter is extremely accurate and due to the variety of tachometers available, there may be differences in the displayed rpm. programming the rev limit a tachometer is required to set the rev limit. the limit is programmed by running the engine at half the desired rpm, then momentarily grounding the gray tach output wire from the msd. a gray jumper wire is supplied to connect to the tach with another tee-splice coming off to use for programming. a switch may also be installed to ease adjustments of the limiter (figure 13). the default rpm limit is 10,000 rpm and the limit is adjustable from 2,000 - over 10,000 rpm.. 1. start the engine and bring the rpm to half the desired rev limit (for a 6,000 rpm limit, raise and hold the rpm to 3,000). 2. while holding the rpm steady, short the gray tach wire to ground for approximately one second. note that the tach will go to zero while grounded. 3. the tach will now display the programmed rev limit amount for two seconds. if this value does not register on the tach, repeat the procedure and try a different ground source. 4. to confrm the rev limit value, turn the ignition key to the on position (without cranking the engine). the rev limit value will be displayed for two seconds on the tachometer. note: this rpm confrmation only displays when the gray wire is being used to trigger the tachometer. to tach optional programming switch jumper gray figure 13 setting the rev limiter. tech notes _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344
limited warranty m sd warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized msd dealer, for a period of one year from the date of the original purchase. this warranty is void for any products purchased through auction websites. if found to be defective as mentioned above, it will be repaired or replaced at the option of msd. any item that is covered under this warranty will be returned free of charge using ground shipping methods. this shall constitute the sole remedy of the purchaser and the sole liability of msd. to the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or ftness. in no event shall msd or its suppliers be liable for special or consequential damages. *intended normal use means that this item is being used as was originally intended and for the original application as sold by msd. any modifcations to this item or if it is used on an application other than what msd markets the product, the warranty will be void. it is the sole responsibility of the customer to determine that this item will work for the application they are intending. msd will accept no liability for custom applications. service in case of malfunction, this msd component will be repaired free of charge according to the terms of the warranty. when returning msd components for warranty service, proof of purchase must be supplied for verifcation. after the warranty period has expired, repair service is based on a minimum and maximum fee. all returns must have a return material authorization (rma) number issued to them before being returned. to obtain an rma number please contact msd customer service at 1 (888) msd-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information. when returning the unit for repair, leave all wires at the length in which you have them installed. be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. the repaired unit will be returned as soon as possible using ground shipping methods (ground shipping is covered by warranty). for more information, call msd at (915) 855-7123. msd technicians are available from 7:00 a.m. to 5:00 p.m. monday - friday (mountain time). msd ?? www.msdperformance.com ? ? ? (915) ? 857-5200 ? ? ? fax ? (915) ? 857-3344 ? 2014 msd llc frm30128 revised 04/14 printed in u.s.a. tech notes _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________
|
